iC-Haus GmbH
iC-Haus GmbH
iC-HF

6-Chan. RS-422 Transceiver supports BiSS bus structure, BiSS bus loopback and Encoder Link
iC-HF is a robust line driver/receiver for industrial control applications using RS422 transmission including BiSS encoder PHY. Operation at 3 V to 5 V is supported including reverse polarity protection, current-limited, short-circuit-proof push-pull drivers allowing high speed at low EMI. The IC's unique feature are:
* RS422 transceiver for BiSS bus structure and BiSS bus loopback
* analog switches bypassing the driver stages (Encoder Link).
The Encoder Link function is triggered by a fail-safe scheme connects outside lines to a device's internal components, for instance if calibration and programming.  

iC-Haus GmbH
iC-Haus GmbH
iC-LGC

21-Bit Optical Position Encoder with BiSS C iC-LGC is an optoelectronic encoder iC for absolute position sensors. Photosensors, amplifiers and comparators, the entire signal conditioning and data processing unit and fast I/O interfaces are monolithically integrated on the chip.From this optical end encoder designs in various diameters are supported, with a conversion core adaptable for the angular position resolution in question, and a data output section selectable with serial (BiSS / SSI) and parallel operating modes (hardware encoder, 8-bit ┬ÁC interface). 

iC-Haus GmbH
iC-Haus GmbH
iC-MB4

iC-MB4 is a single chip BiSS/SSI interface master controller.
BiSS C, BiSS B, SSI and extended SSI devices, sensors and actuators can be fully accessed by iC-MB4. Up to 8 devices can be connected, each with up to 64 bit single cycle data length and up to 16 bit CRC verification.  

iC-Haus GmbH
iC-Haus GmbH
iC-MD

iC-MD processes quadrature encoder signals (with A, B and index) of up to 3 incremental encoders.
Possible counter configurations are up to 48 bit or up to 3 A B counter. Various input signals are applicable: differential RS422 and up to 12 V levels and TTL, CMOS and LVDS logic signals. The device can be accessed via SPI interface or can be operated as a BiSS C or SSI slave device.  

iC-Haus GmbH
iC-Haus GmbH
iC-MH

12 Bit angular Hall encoder
The iC-MH 12-bit angular encoder is a position sensor with integrated Hall sensors for scanning a permanent magnet. The signal conditioning unit generates constant-amplitude sine and cosine voltages that can be used for angle calculation. The resolution can be programmed up to a maximum of 4,096 angular increments per rotation. 

iC-Haus GmbH
iC-Haus GmbH
iC-MH16

The iC-MH16 is an integrated Hall encoder for sensing the angular position of a diametral magnet.
The FlexCount? interpolator can be set to any factor from 1 to 1024 to and achieve up to 4096 angle steps per revolution. ABZ quadrature signal incremental outputs permit up to 200 000 rpm at the highest resolution with an adjustable index pulse postion. U, V and W for the commutation of brushless DC motors with 1 to 16 pole pairs. The outputs are RS422 compatible with adjustable output current and slew rate. iC-MH16 features the BiSS Interface for a fast serial, CRC secures data output and bidirectional register access. The programmed setup can be stored to a non-volatile ROM, based on zapping diodes. 

iC-Haus GmbH
iC-Haus GmbH
iC-MH8

The iC-MH8 is an integrated Hall encoder for sensing the angular position of a diametral magnet.
The amplified Hall voltages are available as complementary analog sine and cosine signals with regulated 1 Vpp differential amplitude. Using the BiSS C interface the output data can be transmitted serially and allows also access to the internal memory of iC-MH8. The configuration and internal parameters can then be stored permanently in a zapping diode based ROM. 

iC-Haus GmbH
iC-Haus GmbH
iC-MHL200

The iC-MHL200 is an integrated Hall encoder for sensing linear and rotary magnetic targets with a 2 mm pole pitch.
A smallest linear position increment of 1 μm can be achieved when the device is operated at 12 bit resolution. The interpolator resolution can be programmed up to a maximum of 4096 increments per magnetic signal period (equivalent to a 4 mm position shift). Using the serial BiSS C interface position data can be transmitted and iC-MHL200 can be accessed for setup. The power-on configuration and internal parameters can then be stored permanently in an on-chip zapping ROM.  

iC-Haus GmbH
iC-Haus GmbH
iC-MHM

iC-MHM is a compact, contactless high-resolution magnetic angle sensor for the on-axis scanning of a diametric magnet.
Its Hall sensor array provides sine/cosine signals output by differential drivers with 1 Vpp. The chip features BiSS C and SPI, multiturn counting, preset on power up and verified cyclically if an external multiturn sensor is connected. The embedded RS422 transceiver allows direct BiSS/SSI line connections and all interface pins are reversepolarity and short-circuit-proof.  

iC-Haus GmbH
iC-Haus GmbH
iC-MN

25-Bit Nonius Encoder
Encoder device iC-MN is a 3-channel, simultaneous sampling sine-to-digital converter which interpolates sine/cosine sensor signals using a high precision SAR converter with a selectable resolution of up to 13 bits. 

iC-Haus GmbH
iC-Haus GmbH
iC-MR

iC-MR combines high-precision analog signal-conditioning with 1 Vpp line drivers for sine/cosine signals and a fast, highresolution sampling sine-to-digital converter.
An absolute data interface (ADI) presets period counting, whereas multiturn and singleturn offset values can adjust the final position data. The chip features BiSS C interface (up to 10 MHz, bidirectional), SSI (up to 4 MHz) or SPI, parallel interface. External KTY temperature sensor; monitoring a motor's temperature are supported including configurable alarms. iC-MR aims at high-resolution position encoders and safety-oriented applications. 

iC-Haus GmbH
iC-Haus GmbH
iC-MU

18-Bit Magnetic Off-Axis Absolute Position Encoder with BiSS C iC-MU is a magnetic hall based encoder iC for absolute position sensors. Hall elements, amplifiers and interpolators, the entire signal conditioning and data processing unit and fast I/O interfaces are monolithically integrated on the chip. From this magnetic end encoder designs in various diameters are supported, with a conversion core adaptable for the angular position resolution in question, and a data output section selectable with serial (BiSS / SSI) or embedded operation (SPI interface) and analog SIN COS output. iC-MU has a pole width of 1.28mm.  

iC-Haus GmbH
iC-Haus GmbH
iC-MU150

18-Bit Magnetic Off-Axis Absolute Position Encoder with BiSS C iC-MU150 is a magnetic hall based encoder iC for absolute position sensors. Hall elements, amplifiers and interpolators, the entire signal conditioning and data processing unit and fast I/O interfaces are monolithically integrated on the chip. From this magnetic end encoder designs in various diameters are supported, with a conversion core adaptable for the angular position resolution in question, and a data output section selectable with serial (BiSS / SSI) or embedded operation (SPI interface) and analog SIN COS output. iC-MU150 has a pole width of 1.50mm.  

iC-Haus GmbH
iC-Haus GmbH
iC-NQC

13-bit Sin/D-Converter With Calibration featuring BiSS C interface
iC-NQC is a monolithic A/D converter which, by applying a count-safe vector follower principle, converts sine/cosine sensor signals with a selectable resolution and hysteresis into angle position data.