Acute Technology Inc.
Acute Technology Inc.
Acute TravelBus BiSS protocol analyzer

Acute TravelBus is a 2 in 1 Analyzer (Protocol & Logic) that is a PC-based, USB 3.0 interface/powered capable to perorm Bus analysis for BiSS C, PWM, Dali, DALI, HID over I²C, I²C, I²S, LIN, MDIO, PMBus, RS232, SMBus, SPI, USB1.1, CAN, Modbus, ProfiBus, RS422, RS485.  

iC-Haus GmbH
iC-Haus GmbH
BiSS (SSI) to PC-USB Adapters


MB3U BiSS to PC-USB Adapter
Ready-to-use USB 2.0 compatible adapter featuring galvanic encoder signal separation and isolated 12V/5V power supply from the USB port or via an external plug-in power supply.

 

iC-Haus GmbH
iC-Haus GmbH
BiSS C (SSI) to PC-USB Adapter


MB4U BiSS C to PC-USB 2.0 Adapter
USB 2.0 compatible adapter featuring fast realtime double buffered high speed data aquisition and 12V/5V power supply from the USB port. Compatible -Ready-to-use- with existing BiSS-Interface DLL software and additional high speed functions.

 

iC-Haus GmbH
iC-Haus GmbH
BiSS C (SSI) to PC-USB isolated Adapter

MB5U BiSS C to PC-USB 2.0 Adapter USB 2.0 compatible adapter featuring isolated fast realtime double buffered high speed data aquisition and 5V power supply from the USB port. Compatible -Ready-to-use- with existing BiSS-Interface DLL software and additional high speed functions. 

Joulefusion
Joulefusion
P201 single channel USB encoder interface


P201-9B USB encoder interface with BiSS C Unidirectional
The P201 series is available with several protocols: BiSS C Unidirectional, SSI and quadrature. The P201-9B model was designed specifically to be compatible with the Renishaw RESOULTE™ absolute encoder with BiSS C Unidirectional protocol. Direct pin compatibility enables straightforward connection of the encoder to a PC.

 

Joulefusion
Joulefusion
P201-9B-RS485

P201-9B-RS485 encoder interface with BiSS C Unidirectional, multiple encoder systems capable
The P201-9B-RS485 is an BiSS interface system developed to allow multiple P2P BiSS encoder (e.g. Renishaw Resolute or LMA or generic 5V SSI encoders) to be connected to an RS485 bus including bus power (8-30VDC). A broadcast capture command allows all connected BiSS encoder positions to be captured at the same instant and then read back sequentially from the addressable modules. Any RS485 master can communicate on ASCII level command and response.  

Robot Makers GmbH
Robot Makers GmbH
MCS-MEA-CUB (BiSS to EtherCAT)

The Measurement System of the Robot Makers GmbH enables synchronous and distributed measuring with a variety of sensor systems including BiSS sensors. The hardware-based implementation of the measurements by means of a powerful FPGA, the recorded values can be pre-processed or even charged in every sample. The Measurement System is primarily characterized by a high measuring frequency of 20 kHz. Using the EtherCAT interface, also provides the ability to run multiple Measurement Systems decentralized, while getting centralized access to the measurements. In this case, it is possible to achieve a synchronization accuracy of less than 1 microseconds. The MCS-MEA-CUB-002 Measurement System cube provides 4x SSI, 2x 3 BiSS (on request). 

S.E.A. GmbH
S.E.A. GmbH
SEA 9521 BiSS

The SEA 9521 BiSS Interface Module connects digital rotary or position encoder with the CompactRIO System from National Instruments™. It supports the full BiSS-C protocol: position data and also the transfer of digital sensor information like current temperature or serial number etc.  

Saleae LLC.
Saleae LLC.
BiSS Protocol Analyzer

Based on the Saleae Logic / Logic16 analyzer and the iC-Haus BiSS Protocol Analyzer Plug-In (DLL) the BiSS C SCD (single cycle data) and register access can be monitored and visualized (see also BiSS AN18 )